Thread Closed
[Fixed] modem prolink phs 600 tidak bisa konek kali linux 2.0
#11
Cari disini mengenai koneksi menggunakan modem prolink om. Jangan males untuk searching.
Quote:~ Tan Hana Wighna Tan Sirna ~

#12
(10-23-2015, 01:29 PM)gnome_selpa Wrote: Cari disini mengenai koneksi menggunakan modem prolink om. Jangan males untuk searching.

Sudah saya cari tetapi tetap tidak mau konek walaupun sudah ada caranya

#13
(10-22-2015, 03:28 PM)BimoSora Wrote:
(10-22-2015, 02:27 PM)gnome_selpa Wrote:
(10-22-2015, 01:18 PM)BimoSora Wrote:
(10-20-2015, 12:03 PM)icehiro Wrote: pake modem prolink 600 juga di kali linux 2 pula, sukses
koneksi pake wvdial, konfigurasi standart

tapi kalau pengen lebih mudah pake sakis3 aja

saya sudah pakai sakis3G yang kedeteksi port yang bukan modem
os kali linux 2.0

Untuk apa pake sakis3g lagi, kan gnome network manager udah terinstal di kali linux 2.0 om.
Tidak bisa koneksi walaupun sudah ada bawaan. Padahal di pengaturan ada settingannya tapi selalu keluar tulisan "Gagal koneksi" padahal apn sudah benar semua

@gnome_selpa di saya koneksi pake gnome network bawaan ga bisa konek om, pake wvdial baru bisa

#14
(10-23-2015, 05:14 PM)icehiro Wrote:
(10-22-2015, 03:28 PM)BimoSora Wrote:
(10-22-2015, 02:27 PM)gnome_selpa Wrote:
(10-22-2015, 01:18 PM)BimoSora Wrote:
(10-20-2015, 12:03 PM)icehiro Wrote: pake modem prolink 600 juga di kali linux 2 pula, sukses
koneksi pake wvdial, konfigurasi standart

tapi kalau pengen lebih mudah pake sakis3 aja

saya sudah pakai sakis3G yang kedeteksi port yang bukan modem
os kali linux 2.0

Untuk apa pake sakis3g lagi, kan gnome network manager udah terinstal di kali linux 2.0 om.
Tidak bisa koneksi walaupun sudah ada bawaan. Padahal di pengaturan ada settingannya tapi selalu keluar tulisan "Gagal koneksi" padahal apn sudah benar semua

@gnome_selpa di saya koneksi pake gnome network bawaan ga bisa konek om, pake wvdial baru bisa

saya pakai wvdial tidak pernah ada yang berhasil, pakai resolvconf juga tidak bisa, pakai sakis3g tidak bisa juga, pakai gnome manager tidak bisa, instal ulang tidak bisa. Harus bagaimana lagi bro

#15
pasti bisa om, ada kesalahan konfigurasi mungkin,
cek lagi deh, linuk itu kayak cewek om kudu lemah lembut jangan kasar"
nih ane kasih konf, cocokin sesuaiin sama punya agan

Code:
[Dialer ii]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Stupid Mode = 1
Modem Type = Analog Modem
Command Line = ATDT
ISDN = 0
New PPPD = yes
Phone = *99#
Modem = /dev/ttyUSB13
Username = indosatgprs
Password = indosat
Baud = 460800

#16
pertama, coba perhatikan lagi message outputnya.

kedua, mulailah dari mengecek log file, gunakan perintah dmesg
dibaca perlahan2x, dengan seksama. lepas dulu modemnya, cek dmesg lalu tancapkan dan cek lagi, liat bagian yang berubah dari keluaran dmesg.

ketiga, coba copy pastekan saja error/message/keluaran layarnya, jangan pakai screenshot. lebih mudah membaca dibandingkan nonton gambar. juga lebih irit bandwidth bagi yang pas pasan.

keempat, terimalah saran dan segala kemungkinan. tidak bisa itu pasti ada yang salah, dan kalau bilang gak ada yang salah pastinya harus bisa bekerja tanpa masalah.
yang penting itu adalah mencari tahu salahnya dimana. jadi bantu diri anda sendiri dengan bekerjasama dengan yang bersedia membantu.
Quote:-= I'm Always N3wb1e =-

#17
coba di wvconf dulu, buat get configuration filenya. abis itu kabarin kesini ya. seharusnya di kalilinux 2.0 itu usb-modem emang plug n play

#18
tetap tidak berhasil walaupun sudah saya configurasi berbagai cara dan saya ingin configurasi pakai cara ini https://www.indonesianbacktrack.or.id/fo...d-300.html tapi pppconfig dan pppoeconf tapi perintah itu tidak ada

#19
(10-26-2015, 01:05 PM)BimoSora Wrote: tetap tidak berhasil walaupun sudah saya configurasi berbagai cara dan saya ingin configurasi pakai cara ini https://www.indonesianbacktrack.or.id/fo...d-300.html tapi pppconfig dan pppoeconf tapi perintah itu tidak
coba wvdialconf, hasilnya paste sini
konfigurasi wvdial.conf paste sini

#20
nih konfigurasinya

root@Aceture:~# sudo wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

Modem Port Scan<*1>: S0   S1   S2   S3  
ttyUSB2<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB2<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB2<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyUSB4<*1>: ATQ0 V1 E1 -- OK
ttyUSB4<*1>: ATQ0 V1 E1 Z -- ATQ0 V1 E1 Z
ttyUSB4<*1>: ATQ0 V1 E1 S0=0 -- ATQ0 V1 E1 S0=0
ttyUSB4<*1>: ATQ0 V1 E1 &C1 -- ATQ0 V1 E1 &C1
ttyUSB4<*1>: ATQ0 V1 E1 &D2 -- ATQ0 V1 E1 &D2
ttyUSB4<*1>: ATQ0 V1 E1 +FCLASS=0 -- OK
ttyUSB4<*1>: Modem Identifier: ATI -- ATI
ttyUSB4<*1>: Speed 9600: AT -- AT
ttyUSB4<*1>: Modem Identifier: ATI -- ATI
ttyUSB4<*1>: nothing.
ttyUSB4<*1>: Max speed is 9600; that should be safe.
ttyUSB4<*1>: Max speed is 9600; that should be safe.
ttyUSB4<*1>: ATQ0 V1 E1 +FCLASS=0 -- ATQ0 V1 E1 +FCLASS=0
ttyUSB4<*1>: and failed too at 115200, giving up.
ttyUSB5<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB5<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB5<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyUSB6<*1>: ATQ0 V1 E1 -- ATQ0 V1 E1
ttyUSB6<*1>: failed with 2400 baud, next try: 9600 baud
ttyUSB6<*1>: ATQ0 V1 E1 -- OK
ttyUSB6<*1>: ATQ0 V1 E1 Z -- failed with 9600 baud, next try: 9600 baud
ttyUSB6<*1>: ATQ0 V1 E1 Z -- ATQ0 V1 E1 Z
ttyUSB6<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB6<*1>: ATQ0 V1 E1 S0=0 &C1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB6<*1>: ATQ0 V1 E1 S0=0 &C1 -- ATQ0 V1 E1 S0=0 &C1
ttyUSB6<*1>: ATQ0 V1 E1 S0=0 &D2 -- OK
ttyUSB6<*1>: ATQ0 V1 E1 S0=0 &D2 +FCLASS=0 -- OK
ttyUSB6<*1>: Modem Identifier: ATI -- Manufacturer: PROLiNK CORPORATION
ttyUSB6<*1>: Max speed is 9600; that should be safe.
ttyUSB6<*1>: ATQ0 V1 E1 S0=0 &D2 +FCLASS=0 -- OK

Found a modem on /dev/ttyUSB6.
Modem configuration written to /etc/wvdial.conf.
ttyUSB6<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &D2 +FCLASS=0"


root@Aceture:~# sudo gedit /etc/wvdial.conf
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &D2 +FCLASS=0
Modem = /dev/ttyUSB6
Command Line = ATDT
Phone = *99#
APN = internet
New PPPD = yes
Password = ”
Modem Type = Analog Modem
Stupid mode = yes
Baud = 9600
Auto DNS = 1
Ask Password = no
ISDN = 0
Username = ”
Carrier Check = yes


root@Aceture:~# lsusb
Bus 001 Device 002: ID 8087:8000 Intel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 0bc2:2312 Seagate RSS LLC
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 008: ID 13d3:3362 IMC Networks Atheros AR3012 Bluetooth 4.0 Adapter
Bus 002 Device 003: ID 04f2:b40a Chicony Electronics Co., Ltd
Bus 002 Device 006: ID 046d:c52f Logitech, Inc. Unifying Receiver
Bus 002 Device 011: ID 19d2:1253 ZTE WCDMA Technologies MSM
Bus 002 Device 002: ID 0a05:7211 Unknown Manufacturer hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


root@Aceture:~# sudo modprobe usbserial vendor=0x19d2product=0x1253
root@Aceture:~# sudo wvdial
--> Wvdial: Internet dialer version 1.61
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT*99#
--> Waiting for carrier.
ATDT*99#
ERROR
--> Invalid dial command.
--> Disconnecting at Thu Oct 15 19:06:58 2015



root@Aceture:~# dmesg
[    0.000000] CPU0 microcode updated early to revision 0x1c, date = 2014-07-03
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.0.0-kali1-amd64 ([email protected]) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 SMP Debian 4.0.4-1+kali2 (2015-06-03)
[    0.000000] Command line: BOOT_IMAGE=/vmlinuz-4.0.0-kali1-amd64 root=UUID=126918e4-a839-460e-8d78-a59baf8bcd3d ro initrd=/install/gtk/initrd.gz quiet
[    0.000000] e820: BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009c7ff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009c800-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000b98e5fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000b98e6000-0x00000000b98ecfff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000b98ed000-0x00000000ba140fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000ba141000-0x00000000ba3befff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ba3bf000-0x00000000c98cefff] usable
[    0.000000] BIOS-e820: [mem 0x00000000c98cf000-0x00000000c9ad6fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000c9ad7000-0x00000000c9e12fff] usable
[    0.000000] BIOS-e820: [mem 0x00000000c9e13000-0x00000000cab1efff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000cab1f000-0x00000000caffefff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000cafff000-0x00000000caffffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000cbc00000-0x00000000cfdfffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000012f1fffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: ASUSTeK COMPUTER INC. X450LCP/X450LCP, BIOS X450LCP.203 10/23/2013
[    0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000000] AGP: No AGP bridge found
[    0.000000] e820: last_pfn = 0x12f200 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-E7FFF uncachable
[    0.000000]   E8000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 0000000000 mask 7F00000000 write-back
[    0.000000]   1 base 0100000000 mask 7FE0000000 write-back
[    0.000000]   2 base 0120000000 mask 7FF0000000 write-back
[    0.000000]   3 base 00E0000000 mask 7FE0000000 uncachable
[    0.000000]   4 base 00D0000000 mask 7FF0000000 uncachable
[    0.000000]   5 base 00CC000000 mask 7FFC000000 uncachable
[    0.000000]   6 base 00CBC00000 mask 7FFFC00000 uncachable
[    0.000000]   7 base 012F800000 mask 7FFF800000 uncachable
[    0.000000]   8 base 012F400000 mask 7FFFC00000 uncachable
[    0.000000]   9 base 012F200000 mask 7FFFE00000 uncachable
[    0.000000] PAT configuration [0-7]: WB  WC  UC- UC  WB  WC  UC- UC  
[    0.000000] e820: update [mem 0xcbc00000-0xffffffff] usable ==> reserved
[    0.000000] e820: last_pfn = 0xcb000 max_arch_pfn = 0x400000000
[    0.000000] found SMP MP-table at [mem 0x000fd860-0x000fd86f] mapped at [ffff8800000fd860]
[    0.000000] Base memory trampoline at [ffff880000096000] 96000 size 24576
[    0.000000] Using GB pages for direct mapping
[    0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[    0.000000]  [mem 0x00000000-0x000fffff] page 4k
[    0.000000] BRK [0x01b12000, 0x01b12fff] PGTABLE
[    0.000000] BRK [0x01b13000, 0x01b13fff] PGTABLE
[    0.000000] BRK [0x01b14000, 0x01b14fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x12f000000-0x12f1fffff]
[    0.000000]  [mem 0x12f000000-0x12f1fffff] page 2M
[    0.000000] BRK [0x01b15000, 0x01b15fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0x120000000-0x12effffff]
[    0.000000]  [mem 0x120000000-0x12effffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x100000000-0x11fffffff]
[    0.000000]  [mem 0x100000000-0x11fffffff] page 2M
[    0.000000] init_memory_mapping: [mem 0x00100000-0xb98e5fff]
[    0.000000]  [mem 0x00100000-0x001fffff] page 4k
[    0.000000]  [mem 0x00200000-0x3fffffff] page 2M
[    0.000000]  [mem 0x40000000-0x7fffffff] page 1G
[    0.000000]  [mem 0x80000000-0xb97fffff] page 2M
[    0.000000]  [mem 0xb9800000-0xb98e5fff] page 4k
[    0.000000] init_memory_mapping: [mem 0xb98ed000-0xba140fff]
[    0.000000]  [mem 0xb98ed000-0xb99fffff] page 4k
[    0.000000]  [mem 0xb9a00000-0xb9ffffff] page 2M
[    0.000000]  [mem 0xba000000-0xba140fff] page 4k
[    0.000000] BRK [0x01b16000, 0x01b16fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0xba3bf000-0xc98cefff]
[    0.000000]  [mem 0xba3bf000-0xba3fffff] page 4k
[    0.000000]  [mem 0xba400000-0xc97fffff] page 2M
[    0.000000]  [mem 0xc9800000-0xc98cefff] page 4k
[    0.000000] BRK [0x01b17000, 0x01b17fff] PGTABLE
[    0.000000] init_memory_mapping: [mem 0xc9ad7000-0xc9e12fff]
[    0.000000]  [mem 0xc9ad7000-0xc9bfffff] page 4k
[    0.000000]  [mem 0xc9c00000-0xc9dfffff] page 2M
[    0.000000]  [mem 0xc9e00000-0xc9e12fff] page 4k
[    0.000000] init_memory_mapping: [mem 0xcafff000-0xcaffffff]
[    0.000000]  [mem 0xcafff000-0xcaffffff] page 4k
[    0.000000] RAMDISK: [mem 0x35a66000-0x36d2afff]
[    0.000000] ACPI: Early table checksum verification disabled
[    0.000000] ACPI: RSDP 0x00000000000F0490 000024 (v02 _ASUS_)
[    0.000000] ACPI: XSDT 0x00000000C9E97090 00009C (v01 _ASUS_ Notebook 01072009 AMI  00010013)
[    0.000000] ACPI: FACP 0x00000000C9EAD708 00010C (v05 _ASUS_ Notebook 01072009 AMI  00010013)
[    0.000000] ACPI: DSDT 0x00000000C9E97248 0164BE (v02 _ASUS_ Notebook 00000012 INTL 20120711)
[    0.000000] ACPI: FACS 0x00000000CAB1C080 000040
[    0.000000] ACPI: APIC 0x00000000C9EAD818 000072 (v03 _ASUS_ Notebook 01072009 AMI  00010013)
[    0.000000] ACPI: FPDT 0x00000000C9EAD890 000044 (v01 _ASUS_ Notebook 01072009 AMI  00010013)
[    0.000000] ACPI: ECDT 0x00000000C9EAD8D8 0000C1 (v01 _ASUS_ Notebook 01072009 AMI. 00000005)
[    0.000000] ACPI: LPIT 0x00000000C9EAD9A0 00005C (v01 _ASUS_ Notebook 00000000 AMI. 00000005)
[    0.000000] ACPI: SSDT 0x00000000C9EADA00 000174 (v01 Intel  zpoddult 00001000 INTL 20120711)
[    0.000000] ACPI: SSDT 0x00000000C9EADB78 000539 (v01 PmRef  Cpu0Ist  00003000 INTL 20120711)
[    0.000000] ACPI: SSDT 0x00000000C9EAE0B8 000AD8 (v01 PmRef  CpuPm    00003000 INTL 20120711)
[    0.000000] ACPI: MCFG 0x00000000C9EAEB90 00003C (v01 _ASUS_ Notebook 01072009 MSFT 00000097)
[    0.000000] ACPI: SSDT 0x00000000C9EAEBD0 003043 (v01 DptfTa DptfTabl 00001000 INTL 20120711)
[    0.000000] ACPI: HPET 0x00000000C9EB1C18 000038 (v01 _ASUS_ Notebook 01072009 AMI. 00000005)
[    0.000000] ACPI: SSDT 0x00000000C9EB1C50 000298 (v01 SataRe SataTabl 00001000 INTL 20120711)
[    0.000000] ACPI: SSDT 0x00000000C9EB1EE8 003EE7 (v01 SaSsdt SaSsdt   00003000 INTL 20091112)
[    0.000000] ACPI: SSDT 0x00000000C9EB5DD0 000BA6 (v01 SgRef  SgPch    00001000 INTL 20120711)
[    0.000000] ACPI: SSDT 0x00000000C9EB6978 001480 (v01 OptRef OptTabl  00001000 INTL 20120711)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at [mem 0x0000000000000000-0x000000012f1fffff]
[    0.000000] NODE_DATA(0) allocated [mem 0x12f1f5000-0x12f1f8fff]
[    0.000000]  [ffffea0000000000-ffffea0004bfffff] PMD -> [ffff88012a800000-ffff88012e7fffff] on node 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.000000]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000012f1fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000001000-0x000000000009bfff]
[    0.000000]   node   0: [mem 0x0000000000100000-0x00000000b98e5fff]
[    0.000000]   node   0: [mem 0x00000000b98ed000-0x00000000ba140fff]
[    0.000000]   node   0: [mem 0x00000000ba3bf000-0x00000000c98cefff]
[    0.000000]   node   0: [mem 0x00000000c9ad7000-0x00000000c9e12fff]
[    0.000000]   node   0: [mem 0x00000000cafff000-0x00000000caffffff]
[    0.000000]   node   0: [mem 0x0000000100000000-0x000000012f1fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000012f1fffff]
[    0.000000] On node 0 totalpages: 1018658
[    0.000000]   DMA zone: 64 pages used for memmap
[    0.000000]   DMA zone: 21 pages reserved
[    0.000000]   DMA zone: 3995 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 12839 pages used for memmap
[    0.000000]   DMA32 zone: 821639 pages, LIFO batch:31
[    0.000000]   Normal zone: 3016 pages used for memmap
[    0.000000]   Normal zone: 193024 pages, LIFO batch:31
[    0.000000] Reserving Intel graphics stolen memory at 0xcbe00000-0xcfdfffff
[    0.000000] ACPI: PM-Timer IO Port: 0x1808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-39
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[    0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009c000-0x0009cfff]
[    0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009ffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[    0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[    0.000000] PM: Registered nosave memory: [mem 0xb98e6000-0xb98ecfff]
[    0.000000] PM: Registered nosave memory: [mem 0xba141000-0xba3befff]
[    0.000000] PM: Registered nosave memory: [mem 0xc98cf000-0xc9ad6fff]
[    0.000000] PM: Registered nosave memory: [mem 0xc9e13000-0xcab1efff]
[    0.000000] PM: Registered nosave memory: [mem 0xcab1f000-0xcaffefff]
[    0.000000] PM: Registered nosave memory: [mem 0xcb000000-0xcbbfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xcbc00000-0xcfdfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xcfe00000-0xf7ffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[    0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[    0.000000] e820: [mem 0xcfe00000-0xf7ffffff] available for PCI devices
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 31 pages/cpu @ffff88012ee00000 s87256 r8192 d31528 u524288
[    0.000000] pcpu-alloc: s87256 r8192 d31528 u524288 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 2 3
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1002718
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-4.0.0-kali1-amd64 root=UUID=126918e4-a839-460e-8d78-a59baf8bcd3d ro initrd=/install/gtk/initrd.gz quiet
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340 using standard form
[    0.000000] AGP: Checking aperture...
[    0.000000] AGP: No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] Memory: 3911588K/4074632K available (5580K kernel code, 1025K rwdata, 1944K rodata, 1248K init, 832K bss, 163044K reserved, 0K cma-reserved)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS:33024 nr_irqs:728 16
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] tsc: Fast TSC calibration using PIT
[    0.000000] tsc: Detected 2294.700 MHz processor
[    0.000042] Calibrating delay loop (skipped), value calculated using timer frequency.. 4589.40 BogoMIPS (lpj=9178800)
[    0.000046] pid_max: default: 32768 minimum: 301
[    0.000053] ACPI: Core revision 20150204
[    0.036436] ACPI: All ACPI Tables successfully acquired
[    0.037996] Security Framework initialized
[    0.038006] AppArmor: AppArmor disabled by boot time parameter
[    0.038008] Yama: disabled by default; enable with sysctl kernel.yama.*
[    0.038366] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.039527] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.040086] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.040094] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.040380] Initializing cgroup subsys blkio
[    0.040383] Initializing cgroup subsys memory
[    0.040389] Initializing cgroup subsys devices
[    0.040392] Initializing cgroup subsys freezer
[    0.040394] Initializing cgroup subsys net_cls
[    0.040398] Initializing cgroup subsys perf_event
[    0.040400] Initializing cgroup subsys net_prio
[    0.040434] CPU: Physical Processor ID: 0
[    0.040435] CPU: Processor Core ID: 0
[    0.040441] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.040442] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[    0.041731] mce: CPU supports 7 MCE banks
[    0.041748] CPU0: Thermal monitoring enabled (TM1)
[    0.041759] process: using mwait in idle threads
[    0.041763] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
[    0.041765] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
[    0.041899] Freeing SMP alternatives memory: 24K (ffffffff81a3a000 - ffffffff81a40000)
[    0.043217] ftrace: allocating 22431 entries in 88 pages
[    0.055688] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[    0.095356] TSC deadline timer enabled
[    0.095359] smpboot: CPU0: Intel® Core™ i5-4200U CPU @ 1.60GHz (fam: 06, model: 45, stepping: 01)
[    0.095395] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
[    0.095423] ... version:                3
[    0.095424] ... bit width:              48
[    0.095425] ... generic registers:      4
[    0.095426] ... value mask:             0000ffffffffffff
[    0.095428] ... max period:             0000ffffffffffff
[    0.095429] ... fixed-purpose events:   3
[    0.095430] ... event mask:             000000070000000f
[    0.096209] x86: Booting SMP configuration:
[    0.096211] .... node  #0, CPUs:      #1
[    0.108940] CPU1 microcode updated early to revision 0x1c, date = 2014-07-03
[    0.112484] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[    0.112597]  #2 #3
[    0.141683] x86: Booted up 1 node, 4 CPUs
[    0.141688] smpboot: Total of 4 processors activated (18357.60 BogoMIPS)
[    0.146763] devtmpfs: initialized
[    0.149706] PM: Registering ACPI NVS region [mem 0xb98e6000-0xb98ecfff] (28672 bytes)
[    0.149709] PM: Registering ACPI NVS region [mem 0xc9e13000-0xcab1efff] (13680640 bytes)
[    0.150282] pinctrl core: initialized pinctrl subsystem
[    0.150469] NET: Registered protocol family 16
[    0.162550] cpuidle: using governor ladder
[    0.172444] cpuidle: using governor menu
[    0.172504] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.172506] ACPI: bus type PCI registered
[    0.172508] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.172608] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.172611] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[    0.172720] PCI: Using configuration type 1 for base access
[    0.183025] ACPI: Added _OSI(Module Device)
[    0.183028] ACPI: Added _OSI(Processor Device)
[    0.183029] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.183031] ACPI: Added _OSI(Processor Aggregator Device)
[    0.186871] ACPI : EC: EC description table is found, configuring boot EC
[    0.190866] ACPI: Executed 2 blocks of module-level executable AML code
[    0.196522] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[    0.203468] ACPI: Dynamic OEM Table Load:
[    0.203477] ACPI: SSDT 0xFFFF880129AB3800 0003D3 (v01 PmRef  Cpu0Cst  00003001 INTL 20120711)
[    0.204750] ACPI: Dynamic OEM Table Load:
[    0.204757] ACPI: SSDT 0xFFFF880129988000 0005AA (v01 PmRef  ApIst    00003000 INTL 20120711)
[    0.206115] ACPI: Dynamic OEM Table Load:
[    0.206120] ACPI: SSDT 0xFFFF880129987800 000119 (v01 PmRef  ApCst    00003000 INTL 20120711)
[    0.208213] ACPI: Interpreter enabled
[    0.208226] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150204/hwxface-580)
[    0.208235] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150204/hwxface-580)
[    0.208263] ACPI: (supports S0 S3 S4 S5)
[    0.208265] ACPI: Using IOAPIC for interrupt routing
[    0.208303] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.228273] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[    0.228282] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[    1.212223] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug PME]
[    1.212513] acpi PNP0A08:00: _OSC: OS now controls [AER PCIeCapability]
[    1.213090] PCI host bridge to bus 0000:00
[    1.213095] pci_bus 0000:00: root bus resource [bus 00-3e]
[    1.213097] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    1.213100] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    1.213102] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    1.213104] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
[    1.213106] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
[    1.213108] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
[    1.213110] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
[    1.213113] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff window]
[    1.213115] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff window]
[    1.213117] pci_bus 0000:00: root bus resource [mem 0xcfe00000-0xfeafffff window]
[    1.213127] pci 0000:00:00.0: [8086:0a04] type 00 class 0x060000
[    1.213270] pci 0000:00:02.0: [8086:0a16] type 00 class 0x030000
[    1.213286] pci 0000:00:02.0: reg 0x10: [mem 0xf7400000-0xf77fffff 64bit]
[    1.213295] pci 0000:00:02.0: reg 0x18: [mem 0xd0000000-0xdfffffff 64bit pref]
[    1.213301] pci 0000:00:02.0: reg 0x20: [io  0xf000-0xf03f]
[    1.213434] pci 0000:00:03.0: [8086:0a0c] type 00 class 0x040300
[    1.213445] pci 0000:00:03.0: reg 0x10: [mem 0xf7a1c000-0xf7a1ffff 64bit]
[    1.213586] pci 0000:00:04.0: [8086:0a03] type 00 class 0x118000
[    1.213601] pci 0000:00:04.0: reg 0x10: [mem 0xf7a10000-0xf7a17fff 64bit]
[    1.213762] pci 0000:00:14.0: [8086:9c31] type 00 class 0x0c0330
[    1.213782] pci 0000:00:14.0: reg 0x10: [mem 0xf7a00000-0xf7a0ffff 64bit]
[    1.213852] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    1.213915] pci 0000:00:14.0: System wakeup disabled by ACPI
[    1.213968] pci 0000:00:16.0: [8086:9c3a] type 00 class 0x078000
[    1.213989] pci 0000:00:16.0: reg 0x10: [mem 0xf7a25000-0xf7a2501f 64bit]
[    1.214061] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[    1.214180] pci 0000:00:1b.0: [8086:9c20] type 00 class 0x040300
[    1.214197] pci 0000:00:1b.0: reg 0x10: [mem 0xf7a18000-0xf7a1bfff 64bit]
[    1.214276] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    1.214340] pci 0000:00:1b.0: System wakeup disabled by ACPI
[    1.214393] pci 0000:00:1c.0: [8086:9c10] type 01 class 0x060400
[    1.214470] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    1.214536] pci 0000:00:1c.0: System wakeup disabled by ACPI
[    1.214586] pci 0000:00:1c.2: [8086:9c14] type 01 class 0x060400
[    1.214665] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[    1.214732] pci 0000:00:1c.2: System wakeup disabled by ACPI
[    1.214781] pci 0000:00:1c.3: [8086:9c16] type 01 class 0x060400
[    1.214860] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[    1.214926] pci 0000:00:1c.3: System wakeup disabled by ACPI
[    1.214976] pci 0000:00:1c.4: [8086:9c18] type 01 class 0x060400
[    1.215055] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    1.215139] pci 0000:00:1c.4: System wakeup disabled by ACPI
[    1.215198] pci 0000:00:1d.0: [8086:9c26] type 00 class 0x0c0320
[    1.215221] pci 0000:00:1d.0: reg 0x10: [mem 0xf7a23000-0xf7a233ff]
[    1.215323] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    1.215406] pci 0000:00:1d.0: System wakeup disabled by ACPI
[    1.215459] pci 0000:00:1f.0: [8086:9c43] type 00 class 0x060100
[    1.215683] pci 0000:00:1f.2: [8086:9c03] type 00 class 0x010601
[    1.215701] pci 0000:00:1f.2: reg 0x10: [io  0xf0b0-0xf0b7]
[    1.215709] pci 0000:00:1f.2: reg 0x14: [io  0xf0a0-0xf0a3]
[    1.215717] pci 0000:00:1f.2: reg 0x18: [io  0xf090-0xf097]
[    1.215725] pci 0000:00:1f.2: reg 0x1c: [io  0xf080-0xf083]
[    1.215734] pci 0000:00:1f.2: reg 0x20: [io  0xf060-0xf07f]
[    1.215742] pci 0000:00:1f.2: reg 0x24: [mem 0xf7a22000-0xf7a227ff]
[    1.215786] pci 0000:00:1f.2: PME# supported from D3hot
[    1.215890] pci 0000:00:1f.3: [8086:9c22] type 00 class 0x0c0500
[    1.215906] pci 0000:00:1f.3: reg 0x10: [mem 0xf7a21000-0xf7a210ff 64bit]
[    1.215929] pci 0000:00:1f.3: reg 0x20: [io  0xf040-0xf05f]
[    1.216060] pci 0000:00:1f.6: [8086:9c24] type 00 class 0x118000
[    1.216093] pci 0000:00:1f.6: reg 0x10: [mem 0xf7a20000-0xf7a20fff 64bit]
[    1.216407] acpiphp: Slot [1] registered
[    1.216413] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    1.216556] pci 0000:02:00.0: [1969:10a1] type 00 class 0x020000
[    1.216594] pci 0000:02:00.0: reg 0x10: [mem 0xf7900000-0xf793ffff 64bit]
[    1.216611] pci 0000:02:00.0: reg 0x18: [io  0xe000-0xe07f]
[    1.216757] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    1.216800] pci 0000:02:00.0: System wakeup disabled by ACPI
[    1.224090] pci 0000:00:1c.2: PCI bridge to [bus 02]
[    1.224094] pci 0000:00:1c.2:   bridge window [io  0xe000-0xefff]
[    1.224098] pci 0000:00:1c.2:   bridge window [mem 0xf7900000-0xf79fffff]
[    1.224223] pci 0000:03:00.0: [168c:0032] type 00 class 0x028000
[    1.224251] pci 0000:03:00.0: reg 0x10: [mem 0xf7800000-0xf787ffff 64bit]
[    1.224308] pci 0000:03:00.0: reg 0x30: [mem 0xf7880000-0xf788ffff pref]
[    1.224387] pci 0000:03:00.0: supports D1 D2
[    1.224389] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    1.224423] pci 0000:03:00.0: System wakeup disabled by ACPI
[    1.232086] pci 0000:00:1c.3: PCI bridge to [bus 03]
[    1.232092] pci 0000:00:1c.3:   bridge window [mem 0xf7800000-0xf78fffff]
[    1.232203] pci 0000:04:00.0: [10de:1140] type 00 class 0x030200
[    1.232229] pci 0000:04:00.0: reg 0x10: [mem 0xf6000000-0xf6ffffff]
[    1.232253] pci 0000:04:00.0: reg 0x14: [mem 0xe0000000-0xefffffff 64bit pref]
[    1.232277] pci 0000:04:00.0: reg 0x1c: [mem 0xf0000000-0xf1ffffff 64bit pref]
[    1.232292] pci 0000:04:00.0: reg 0x24: [io  0xd000-0xd07f]
[    1.232308] pci 0000:04:00.0: reg 0x30: [mem 0xf7000000-0xf707ffff pref]
[    1.232440] pci 0000:04:00.0: System wakeup disabled by ACPI
[    1.240089] pci 0000:00:1c.4: PCI bridge to [bus 04]
[    1.240093] pci 0000:00:1c.4:   bridge window [io  0xd000-0xdfff]
[    1.240097] pci 0000:00:1c.4:   bridge window [mem 0xf6000000-0xf70fffff]
[    1.240102] pci 0000:00:1c.4:   bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
[    1.240138] acpi PNP0A08:00: Disabling ASPM (FADT indicates it is unsupported)
[    1.241393] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12)
[    1.241456] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 12) *0, disabled.
[    1.241518] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 12)
[    1.241578] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 12)
[    1.241636] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 12) *0, disabled.
[    1.241695] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 12) *0, disabled.
[    1.241755] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 12)
[    1.241814] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *4 5 6 7 10 12)
[    1.242238] ACPI: Enabled 4 GPEs in block 00 to 7F
[    1.242344] ACPI : EC: GPE = 0xa, I/O: command/status = 0x66, data = 0x62
[    1.242481] vgaarb: setting as boot device: PCI:0000:00:02.0
[    1.242484] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[    1.242488] vgaarb: loaded
[    1.242489] vgaarb: bridge control possible 0000:00:02.0
[    1.242623] PCI: Using ACPI for IRQ routing
[    1.244132] PCI: pci_cache_line_size set to 64 bytes
[    1.244186] e820: reserve RAM buffer [mem 0x0009c800-0x0009ffff]
[    1.244188] e820: reserve RAM buffer [mem 0xb98e6000-0xbbffffff]
[    1.244190] e820: reserve RAM buffer [mem 0xba141000-0xbbffffff]
[    1.244192] e820: reserve RAM buffer [mem 0xc98cf000-0xcbffffff]
[    1.244194] e820: reserve RAM buffer [mem 0xc9e13000-0xcbffffff]
[    1.244196] e820: reserve RAM buffer [mem 0xcb000000-0xcbffffff]
[    1.244198] e820: reserve RAM buffer [mem 0x12f200000-0x12fffffff]
[    1.244381] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[    1.244388] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[    1.246415] Switched to clocksource hpet
[    1.253080] pnp: PnP ACPI init
[    1.253231] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[    1.253236] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[    1.253567] system 00:01: [io  0x0680-0x069f] has been reserved
[    1.253570] system 00:01: [io  0xffff] has been reserved
[    1.253573] system 00:01: [io  0xffff] has been reserved
[    1.253575] system 00:01: [io  0xffff] has been reserved
[    1.253577] system 00:01: [io  0x1c00-0x1cfe] has been reserved
[    1.253579] system 00:01: [io  0x1d00-0x1dfe] has been reserved
[    1.253582] system 00:01: [io  0x1e00-0x1efe] has been reserved
[    1.253584] system 00:01: [io  0x1f00-0x1ffe] has been reserved
[    1.253586] system 00:01: [io  0x1800-0x18fe] could not be reserved
[    1.253589] system 00:01: [io  0x164e-0x164f] has been reserved
[    1.253592] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.253630] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    1.253698] system 00:03: [io  0x1854-0x1857] has been reserved
[    1.253701] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[    1.253767] system 00:04: [io  0x04d0-0x04d1] has been reserved
[    1.253769] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.253817] system 00:05: [io  0x0240-0x0259] has been reserved
[    1.253819] system 00:05: [io  0x0380-0x038f] has been reserved
[    1.253821] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.253901] pnp 00:06: Plug and Play ACPI device, IDs ETD0108 SYN0a00 SYN0002 PNP0f03 PNP0f13 PNP0f12 (active)
[    1.253952] pnp 00:07: Plug and Play ACPI device, IDs ATK3001 PNP030b (active)
[    1.254367] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.254726] system 00:09: [mem 0xfed1c000-0xfed1ffff] has been reserved
[    1.254730] system 00:09: [mem 0xfed10000-0xfed17fff] has been reserved
[    1.254732] system 00:09: [mem 0xfed18000-0xfed18fff] has been reserved
[    1.254735] system 00:09: [mem 0xfed19000-0xfed19fff] has been reserved
[    1.254737] system 00:09: [mem 0xf8000000-0xfbffffff] has been reserved
[    1.254741] system 00:09: [mem 0xfed20000-0xfed3ffff] has been reserved
[    1.254743] system 00:09: [mem 0xfed90000-0xfed93fff] has been reserved
[    1.254746] system 00:09: [mem 0xfed45000-0xfed8ffff] has been reserved
[    1.254748] system 00:09: [mem 0xff000000-0xffffffff] has been reserved
[    1.254751] system 00:09: [mem 0xfee00000-0xfeefffff] could not be reserved
[    1.254754] system 00:09: [mem 0xf7fdf000-0xf7fdffff] has been reserved
[    1.254756] system 00:09: [mem 0xf7fe0000-0xf7feffff] has been reserved
[    1.254759] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.254862] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.255303] pnp: PnP ACPI: found 11 devices
[    1.262214] pci 0000:00:1c.0: PCI bridge to [bus 01]
[    1.262227] pci 0000:00:1c.2: PCI bridge to [bus 02]
[    1.262231] pci 0000:00:1c.2:   bridge window [io  0xe000-0xefff]
[    1.262236] pci 0000:00:1c.2:   bridge window [mem 0xf7900000-0xf79fffff]
[    1.262244] pci 0000:00:1c.3: PCI bridge to [bus 03]
[    1.262249] pci 0000:00:1c.3:   bridge window [mem 0xf7800000-0xf78fffff]
[    1.262258] pci 0000:00:1c.4: PCI bridge to [bus 04]
[    1.262261] pci 0000:00:1c.4:   bridge window [io  0xd000-0xdfff]
[    1.262266] pci 0000:00:1c.4:   bridge window [mem 0xf6000000-0xf70fffff]
[    1.262270] pci 0000:00:1c.4:   bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
[    1.262277] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    1.262280] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    1.262282] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    1.262284] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff window]
[    1.262286] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff window]
[    1.262288] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff window]
[    1.262290] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff window]
[    1.262292] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff window]
[    1.262294] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff window]
[    1.262297] pci_bus 0000:00: resource 13 [mem 0xcfe00000-0xfeafffff window]
[    1.262299] pci_bus 0000:02: resource 0 [io  0xe000-0xefff]
[    1.262301] pci_bus 0000:02: resource 1 [mem 0xf7900000-0xf79fffff]
[    1.262304] pci_bus 0000:03: resource 1 [mem 0xf7800000-0xf78fffff]
[    1.262306] pci_bus 0000:04: resource 0 [io  0xd000-0xdfff]
[    1.262308] pci_bus 0000:04: resource 1 [mem 0xf6000000-0xf70fffff]
[    1.262310] pci_bus 0000:04: resource 2 [mem 0xe0000000-0xf1ffffff 64bit pref]
[    1.262378] NET: Registered protocol family 2
[    1.262618] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    1.262713] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    1.262803] TCP: Hash tables configured (established 32768 bind 32768)
[    1.262823] TCP: reno registered
[    1.262831] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    1.262851] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    1.262922] NET: Registered protocol family 1
[    1.262943] pci 0000:00:02.0: Video device with shadowed ROM
[    1.286516] pci 0000:02:00.0: set MSI_INTX_DISABLE_BUG flag
[    1.286540] PCI: CLS 64 bytes, default 64
[    1.286596] Unpacking initramfs...
[    1.778493] Freeing initrd memory: 19220K (ffff880035a66000 - ffff880036d2b000)
[    1.778517] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    1.778520] software IO TLB [mem 0xc58cf000-0xc98cf000] (64MB) mapped at [ffff8800c58cf000-ffff8800c98cefff]
[    1.778772] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
[    1.778845] microcode: CPU0 sig=0x40651, pf=0x40, revision=0x1c
[    1.778856] microcode: CPU1 sig=0x40651, pf=0x40, revision=0x1c
[    1.778866] microcode: CPU2 sig=0x40651, pf=0x40, revision=0x1c
[    1.778873] microcode: CPU3 sig=0x40651, pf=0x40, revision=0x1c
[    1.778942] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[    1.779315] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    1.779362] audit: initializing netlink subsys (disabled)
[    1.779382] audit: type=2000 audit(1446095250.792:1): initialized
[    1.779820] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.779849] zpool: loaded
[    1.780044] VFS: Disk quotas dquot_6.5.2
[    1.780066] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.780540] alg: No test for stdrng (krng)
[    1.780578] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    1.780618] io scheduler noop registered
[    1.780621] io scheduler deadline registered
[    1.780637] io scheduler cfq registered (default)
[    1.781296] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.781318] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.781350] intel_idle: MWAIT substates: 0x11142120
[    1.781352] intel_idle: v0.4 model 0x45
[    1.781353] intel_idle: lapic_timer_reliable_states 0xffffffff
[    1.781719] GHES: HEST is not enabled!
[    1.781803] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.782391] Linux agpgart interface v0.103
[    1.782463] AMD IOMMUv2 driver by Joerg Roedel <[email protected]>
[    1.782465] AMD IOMMUv2 functionality not available on this system
[    1.782569] i8042: PNP: PS/2 Controller [PNP030bTongueS2K,PNP0f03TongueS2M] at 0x60,0x64 irq 1,12
[    1.807101] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.807107] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.807274] mousedev: PS/2 mouse device common for all mice
[    1.807317] rtc_cmos 00:02: RTC can wake from S4
[    1.807472] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    1.807503] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    1.807523] Intel P-state driver initializing.
[    1.807691] ledtrig-cpu: registered to indicate activity on CPUs
[    1.808201] TCP: cubic registered
[    1.808284] NET: Registered protocol family 10
[    1.808743] mip6: Mobile IPv6
[    1.808776] NET: Registered protocol family 17
[    1.808797] mpls_gso: MPLS GSO support
[    1.809736] registered taskstats version 1
[    1.811229] rtc_cmos 00:02: setting system clock to 2015-10-29 05:07:32 UTC (1446095252)
[    1.811426] PM: Hibernation image not present or could not be loaded.
[    1.812048] Freeing unused kernel memory: 1248K (ffffffff81902000 - ffffffff81a3a000)
[    1.812051] Write protecting the kernel read-only data: 8192k
[    1.812614] Freeing unused kernel memory: 552K (ffff880001576000 - ffff880001600000)
[    1.812744] Freeing unused kernel memory: 104K (ffff8800017e6000 - ffff880001800000)
[    1.840425] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.847352] systemd-udevd[77]: starting version 215
[    1.847582] random: systemd-udevd urandom read with 3 bits of entropy available
[    1.855048] sdhci: Secure Digital Host Controller Interface driver
[    1.855051] sdhci: Copyright© Pierre Ossman
[    1.856478] hidraw: raw HID events driver © Jiri Kosina
[    1.865250] thermal LNXTHERM:00: registered as thermal_zone0
[    1.865254] ACPI: Thermal Zone [THRM] (35 C)
[    1.867101] SCSI subsystem initialized
[    1.868962] ACPI: bus type USB registered
[    1.868994] usbcore: registered new interface driver usbfs
[    1.869007] usbcore: registered new interface driver hub
[    1.869034] libata version 3.00 loaded.
[    1.870108] usbcore: registered new device driver usb
[    1.870334] ahci 0000:00:1f.2: version 3.0
[    1.870522] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[    1.870663] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.870911] ehci-pci: EHCI PCI platform driver
[    1.871558] AVX2 version of gcm_enc/dec engaged.
[    1.871561] AES CTR mode by8 optimization enabled
[    1.874536] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni)
[    1.875366] alx 0000:02:00.0 eth0: Qualcomm Atheros AR816x/AR817x Ethernet [bc:ee:7b:b4:11:37]
[    1.877904] alg: No test for crc32 (crc32-pclmul)
[    1.886099] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x3 impl SATA mode
[    1.886104] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo only pio slum part deso sadm sds apst
[    1.886959] scsi host0: ahci
[    1.887102] scsi host1: ahci
[    1.887234] scsi host2: ahci
[    1.887370] scsi host3: ahci
[    1.887432] ata1: SATA max UDMA/133 abar m2048@0xf7a22000 port 0xf7a22100 irq 40
[    1.887435] ata2: SATA max UDMA/133 abar m2048@0xf7a22000 port 0xf7a22180 irq 40
[    1.887436] ata3: DUMMY
[    1.887438] ata4: DUMMY
[    1.887655] ehci-pci 0000:00:1d.0: EHCI Host Controller
[    1.887664] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    1.887681] ehci-pci 0000:00:1d.0: debug port 2
[    1.891591] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[    1.891603] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7a23000
[    1.902072] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[    1.902120] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.902123] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.902125] usb usb1: Product: EHCI Host Controller
[    1.902126] usb usb1: Manufacturer: Linux 4.0.0-kali1-amd64 ehci_hcd
[    1.902128] usb usb1: SerialNumber: 0000:00:1d.0
[    1.902310] hub 1-0:1.0: USB hub found
[    1.902321] hub 1-0:1.0: 2 ports detected
[    1.902629] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    1.902640] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[    1.902726] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000b810
[    1.902732] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[    1.902876] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.902879] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.902881] usb usb2: Product: xHCI Host Controller
[    1.902883] usb usb2: Manufacturer: Linux 4.0.0-kali1-amd64 xhci-hcd
[    1.902884] usb usb2: SerialNumber: 0000:00:14.0
[    1.903059] hub 2-0:1.0: USB hub found
[    1.903082] hub 2-0:1.0: 9 ports detected
[    1.905627] xhci_hcd 0000:00:14.0: xHCI Host Controller
[    1.905631] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[    1.905656] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
[    1.905658] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.905659] usb usb3: Product: xHCI Host Controller
[    1.905660] usb usb3: Manufacturer: Linux 4.0.0-kali1-amd64 xhci-hcd
[    1.905662] usb usb3: SerialNumber: 0000:00:14.0
[    1.905761] hub 3-0:1.0: USB hub found
[    1.905768] hub 3-0:1.0: 4 ports detected
[    2.118066] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
[    2.135777] usb 3-1: New USB device found, idVendor=0bc2, idProduct=2312
[    2.135782] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.135784] usb 3-1: Product: Expansion
[    2.135786] usb 3-1: Manufacturer: Seagate
[    2.135787] usb 3-1: SerialNumber: NA49JH0X
[    2.137521] usbcore: registered new interface driver usb-storage
[    2.138319] scsi host4: uas
[    2.138378] usbcore: registered new interface driver uas
[    2.139411] scsi 4:0:0:0: Direct-Access     Seagate  Expansion        0636 PQ: 0 ANSI: 6
[    2.205957] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[    2.207056] ata1.00: ATA-8: HGST HTS545050A7E680, GG2OAF10, max UDMA/133
[    2.207061] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    2.208270] ata1.00: configured for UDMA/133
[    2.208531] scsi 0:0:0:0: Direct-Access     ATA      HGST HTS545050A7 AF10 PQ: 0 ANSI: 5
[    2.213962] usb 1-1: new high-speed USB device number 2 using ehci-pci
[    2.341891] usb 2-2: new full-speed USB device number 2 using xhci_hcd
[    2.346620] usb 1-1: New USB device found, idVendor=8087, idProduct=8000
[    2.346624] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.346962] hub 1-1:1.0: USB hub found
[    2.347045] hub 1-1:1.0: 8 ports detected
[    2.470981] usb 2-2: New USB device found, idVendor=0a05, idProduct=7211
[    2.470985] usb 2-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.470987] usb 2-2: Product: USB2.0 HUB
[    2.471125] usb 2-2: ep 0x81 - rounding interval to 1024 microframes, ep desc says 2040 microframes
[    2.471423] hub 2-2:1.0: USB hub found
[    2.471602] hub 2-2:1.0: 4 ports detected
[    2.525797] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.529916] ata2.00: ATAPI: TSSTcorp CDDVDW SU-228CB, AS00, max UDMA/100
[    2.534603] ata2.00: configured for UDMA/100
[    2.538010] scsi 1:0:0:0: CD-ROM            TSSTcorp CDDVDW SU-228CB  AS00 PQ: 0 ANSI: 5
[    2.549474] sd 0:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[    2.549481] sd 0:0:0:0: [sdb] 4096-byte physical blocks
[    2.549519] sd 0:0:0:0: [sdb] Write Protect is off
[    2.549523] sd 0:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    2.549539] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.550018] sd 4:0:0:0: [sda] 976773167 512-byte logical blocks: (500 GB/465 GiB)
[    2.550032] sd 4:0:0:0: Attached scsi generic sg0 type 0
[    2.550085] sd 0:0:0:0: Attached scsi generic sg1 type 0
[    2.550142] sr 1:0:0:0: Attached scsi generic sg2 type 5
[    2.551062] sd 4:0:0:0: [sda] Write Protect is off
[    2.551065] sd 4:0:0:0: [sda] Mode Sense: 2b 00 10 08
[    2.551838] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[    2.559585]  sda: sda1
[    2.562490] sd 4:0:0:0: [sda] Attached SCSI disk
[    2.565334] sr 1:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.565337] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.565496] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.641718] usb 2-5: new high-speed USB device number 3 using xhci_hcd
[    2.660635]  sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 >
[    2.661593] sd 0:0:0:0: [sdb] Attached SCSI disk
[    2.777625] tsc: Refined TSC clocksource calibration: 2294.687 MHz
[    2.802594] usb 2-5: New USB device found, idVendor=04f2, idProduct=b40a
[    2.802597] usb 2-5: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[    2.802599] usb 2-5: Product: USB2.0 HD UVC WebCam
[    2.802600] usb 2-5: Manufacturer: Chicony Electronics Co.,Ltd.
[    2.802602] usb 2-5: SerialNumber: 0x0001
[    2.969532] usb 2-6: new full-speed USB device number 4 using xhci_hcd
[    3.099130] usb 2-6: New USB device found, idVendor=13d3, idProduct=3362
[    3.099134] usb 2-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    3.099137] usb 2-6: Product: Bluetooth USB Host Controller
[    3.099139] usb 2-6: Manufacturer: Atheros Communications
[    3.099140] usb 2-6: SerialNumber: Alaska Day 2006
[    3.289506] usb 2-2.3: new full-speed USB device number 5 using xhci_hcd
[    3.378096] usb 2-2.3: not running at top speed; connect to a high speed hub
[    3.380592] usb 2-2.3: New USB device found, idVendor=19d2, idProduct=2000
[    3.380595] usb 2-2.3: New USB device strings: Mfr=3, Product=2, SerialNumber=4
[    3.380597] usb 2-2.3: Product: PROLiNK WCDMA Technology MSM
[    3.380599] usb 2-2.3: Manufacturer: PROLiNK,Incorporated
[    3.380601] usb 2-2.3: SerialNumber: PHS600PROD010000
[    3.382602] usb-storage 2-2.3:1.0: USB Mass Storage device detected
[    3.382727] scsi host5: usb-storage 2-2.3:1.0
[    3.453330] usb 2-2.4: new full-speed USB device number 6 using xhci_hcd
[    3.543361] usb 2-2.4: New USB device found, idVendor=046d, idProduct=c52f
[    3.543364] usb 2-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    3.543367] usb 2-2.4: Product: USB Receiver
[    3.543368] usb 2-2.4: Manufacturer: Logitech
[    3.547454] usbcore: registered new interface driver usbhid
[    3.547457] usbhid: USB HID core driver
[    3.548145] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2.4/2-2.4:1.0/0003:046D:C52F.0001/input/input2
[    3.548270] hid-generic 0003:046D:C52F.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:14.0-2.4/input0
[    3.549057] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2.4/2-2.4:1.1/0003:046D:C52F.0002/input/input3
[    3.601295] hid-generic 0003:046D:C52F.0002: input,hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:14.0-2.4/input1
[    3.777276] Switched to clocksource tsc
[    3.819297] random: nonblocking pool is initialized
[    3.936943] device-mapper: uevent: version 1.0.3
[    3.937010] device-mapper: ioctl: 4.30.0-ioctl (2014-12-22) initialised: [email protected]
[    3.942277] PM: Starting manual resume from disk
[    3.942282] PM: Hibernation image partition 8:25 present
[    3.942283] PM: Looking for hibernation image.
[    3.966319] PM: Image not found (code -22)
[    3.966322] PM: Hibernation image not present or could not be loaded.
[    4.234057] EXT4-fs (sdb7): mounted filesystem with ordered data mode. Opts: (null)
[    4.382148] scsi 5:0:0:0: CD-ROM            HSPA     USB SCSI CD-ROM  2.31 PQ: 0 ANSI: 2
[    4.382777] scsi 5:0:0:1: Direct-Access     PROLiNK  MMC Storage      2.31 PQ: 0 ANSI: 2
[    4.384697] sr 5:0:0:0: [sr1] scsi-1 drive
[    4.384856] sr 5:0:0:0: Attached scsi CD-ROM sr1
[    4.384961] sr 5:0:0:0: Attached scsi generic sg3 type 5
[    4.385727] sd 5:0:0:1: Attached scsi generic sg4 type 0
[    4.433762] sd 5:0:0:1: ioctl_internal_command return code = 8070000
[    4.433768] sd 5:0:0:1: Sense Key : Hardware Error [current]
[    4.433771] sd 5:0:0:1: Add. Sense: No additional sense information
[    4.434788] sd 5:0:0:1: [sdc] Attached SCSI removable disk
[    4.481610] sd 5:0:0:1: ioctl_internal_command return code = 8070000
[    4.481615] sd 5:0:0:1: Sense Key : Hardware Error [current]
[    4.481617] sd 5:0:0:1: Add. Sense: No additional sense information
[    4.945894] systemd[1]: RTC configured in localtime, applying delta of 420 minutes to system time.
[    6.763014] fuse init (API version 7.23)
[    7.347607] systemd-udevd[245]: starting version 215
[    8.042726] usb 3-1: USB disconnect, device number 2
[    8.043162] sd 4:0:0:0: [sda] Synchronizing SCSI cache
[    8.162617] sd 4:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[    8.242556] usb 2-1: new high-speed USB device number 7 using xhci_hcd
[    8.253455] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    8.286974] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input4
[    8.287761] ACPI: Lid Switch [LID]
[    8.287840] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input5
[    8.287846] ACPI: Sleep Button [SLPB]
[    8.287917] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[    8.287921] ACPI: Power Button [PWRF]
[    8.487097] ACPI Warning: SystemIO range 0x000000000000F040-0x000000000000F05F conflicts with OpRegion 0x000000000000F040-0x000000000000F04F (\SMB0) (20150204/utaddress-254)
[    8.487106] ACPI Warning: SystemIO range 0x000000000000F040-0x000000000000F05F conflicts with OpRegion 0x000000000000F040-0x000000000000F04F (\_SB_.PCI0.SBUS.SMBI) (20150204/utaddress-254)
[    8.487111] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    8.620612] wmi: Mapper loaded
[    8.885719] sound hdaudioC1D0: CX20751/2: BIOS auto-probing.
[    8.886021] sound hdaudioC1D0: autoconfig for CX20751/2: line_outs=1 (0x17/0x0/0x0/0x0/0x0) typeConfusedpeaker
[    8.886024] sound hdaudioC1D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[    8.886026] sound hdaudioC1D0:    hp_outs=1 (0x16/0x0/0x0/0x0/0x0)
[    8.886028] sound hdaudioC1D0:    mono: mono_out=0x0
[    8.886030] sound hdaudioC1D0:    inputs:
[    8.886032] sound hdaudioC1D0:      Internal Mic=0x1a
[    8.886034] sound hdaudioC1D0:      Mic=0x19
[    8.886671] sound hdaudioC1D0: Enable sync_write for stable communication
[    8.888505] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card1/hdaudioC1D0/input7
[    8.888614] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input8
[    8.888641] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input9
[    9.036309] ACPI: AC Adapter [AC0] (on-line)
[    9.052322] ACPI: Battery Slot [BAT0] (battery present)
[    9.060789] [drm] Initialized drm 1.1.0 20060810
[    9.574483] input: PC Speaker as /devices/platform/pcspkr/input/input11
[    9.742785] cfg80211: Calling CRDA to update world regulatory domain
[    9.807010] asus_wmi: ASUS WMI generic driver loaded
[    9.807669] asus_wmi: Initialization: 0x1
[    9.807708] asus_wmi: BIOS WMI version: 7.9
[    9.807751] asus_wmi: SFUN value: 0x4a0877
[    9.808721] input: Asus WMI hotkeys as /devices/platform/asus-nb-wmi/input/input12
[    9.813439] asus_wmi: Backlight controlled by ACPI video driver
[    9.850876] iTCO_vendor_support: vendor-support=0
[   10.006519] [drm] Memory usable by graphics device = 2048M
[   10.006522] [drm] Replacing VGA console driver
[   10.007143] Console: switching to colour dummy device 80x25
[   10.029611] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   10.029614] [drm] Driver supports precise vblank timestamp query.
[   10.029708] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[   10.043105] intel_rapl: Found RAPL domain package
[   10.043108] intel_rapl: Found RAPL domain core
[   10.043109] intel_rapl: Found RAPL domain uncore
[   10.043111] intel_rapl: Found RAPL domain dram
[   10.088958] Bluetooth: Core ver 2.20
[   10.088973] NET: Registered protocol family 31
[   10.088975] Bluetooth: HCI device and connection manager initialized
[   10.088978] Bluetooth: HCI socket layer initialized
[   10.088980] Bluetooth: L2CAP socket layer initialized
[   10.088988] Bluetooth: SCO socket layer initialized
[   10.094503] [Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
[   10.095059] fbcon: inteldrmfb (fb0) is primary device
[   10.096731] ACPI: Video Device [PEGP] (multi-head: yes  rom: yes  post: no)
[   10.099321] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:05/LNXVIDEO:00/input/input13
[   10.100854] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   10.103498] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input14
[   10.103599] snd_hda_intel 0000:00:03.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[   10.103601] [drm] Initialized i915 1.6.0 20150130 for 0000:00:02.0 on minor 0
[   10.105785] usbcore: registered new interface driver btusb
[   10.128750] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[   10.128791] iTCO_wdt: Found a Lynx Point_LP TCO device (Version=2, TCOBASE=0x1860)
[   10.128924] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   10.235145] usb 2-6: firmware: direct-loading firmware ar3k/AthrBT_0x01020200.dfu
[   10.269160] input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input15
[   10.325924] usb 2-6: firmware: direct-loading firmware ar3k/ramps_0x01020200_40.dfu
[   10.329177] usbcore: registered new interface driver ath3k
[   10.329199] usb 2-6: USB disconnect, device number 4
[   10.451685] MXM: GUID detected in BIOS
[   10.451768] ACPI Warning: \_SB_.PCI0.RP05.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   10.451815] ACPI Warning: \_SB_.PCI0.RP05.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
[   10.452003] pci 0000:04:00.0: optimus capabilities: enabled, status dynamic power,
[   10.452004] VGA switcheroo: detected Optimus DSM method \_SB_.PCI0.RP05.PEGP handle
[   10.452266] psmouse serio1: elantech: assuming hardware version 4 (with firmware version 0x361f01)
[   10.467434] psmouse serio1: elantech: Synaptics capabilities query result 0x00, 0x15, 0x0c.
[   10.477651] ath: phy0: Disable PLL PowerSave
[   10.484941] ath: EEPROM regdomain: 0x60
[   10.484942] ath: EEPROM indicates we should expect a direct regpair map
[   10.484944] ath: Country alpha2 being used: 00
[   10.484944] ath: Regpair used: 0x60
[   10.507058] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   10.507312] ieee80211 phy0: Atheros AR9485 Rev:1 mem=0xffffc90004a00000, irq=19
[   10.536926] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input10
[   10.601277] usb 2-6: new full-speed USB device number 8 using xhci_hcd
[   10.738136] sd 5:0:0:1: ioctl_internal_command return code = 8070000
[   10.738139] sd 5:0:0:1: Sense Key : Hardware Error [current]
[   10.738140] sd 5:0:0:1: Add. Sense: No additional sense information
[   10.750149] sr 5:0:0:0: ioctl_internal_command return code = 8070000
[   10.750151] sr 5:0:0:0: Sense Key : Hardware Error [current]
[   10.750153] sr 5:0:0:0: Add. Sense: No additional sense information
[   10.782871] media: Linux media interface: v0.10
[   10.810827] Linux video capture interface: v2.00
[   10.853805] uvcvideo: Found UVC 1.00 device USB2.0 HD UVC WebCam (04f2:b40a)
[   10.855055] input: USB2.0 HD UVC WebCam as /devices/pci0000:00/0000:00:14.0/usb2/2-5/2-5:1.0/input/input16
[   10.855128] usbcore: registered new interface driver uvcvideo
[   10.855128] USB Video Class driver (1.1.1)
[   10.977079] cfg80211: World regulatory domain updated:
[   10.977081] cfg80211:  DFS brother region: unset
[   10.977081] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   10.977084] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.977085] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.977086] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   10.977087] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   10.977089] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   10.977090] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   10.977091] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   10.977092] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   11.165037] Console: switching to colour frame buffer device 170x48
[   11.168576] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[   11.168579] i915 0000:00:02.0: registered panic notifier
[   11.168907] nouveau  [  DEVICE][0000:04:00.0] BOOT0  : 0x0d7000a2
[   11.168913] nouveau  [  DEVICE][0000:04:00.0] Chipset: GF117 (NVD7)
[   11.168915] nouveau  [  DEVICE][0000:04:00.0] Family : NVC0
[   11.182877] nouveau  [   VBIOS][0000:04:00.0] using image from ACPI
[   11.182950] nouveau  [   VBIOS][0000:04:00.0] BIT signature found
[   11.182952] nouveau  [   VBIOS][0000:04:00.0] version 75.17.5c.00.01
[   11.183114] nouveau  [   VBIOS][0000:04:00.0] running init tables
[   11.265476] nouveau  [     PMC][0000:04:00.0] MSI interrupts enabled
[   11.265519] nouveau W[     PFB][0000:04:00.0][0x00000000] reclocking of this ram type unsupported
[   11.265521] nouveau  [     PFB][0000:04:00.0] RAM type: DDR3
[   11.265522] nouveau  [     PFB][0000:04:00.0] RAM size: 2048 MiB
[   11.265523] nouveau  [     PFB][0000:04:00.0]    ZCOMP: 0 tags
[   12.544166] nouveau  [  PTHERM][0000:04:00.0] FAN control: none / external
[   12.544187] nouveau  [  PTHERM][0000:04:00.0] internal sensor: no
[   12.544249] nouveau  [     CLK][0000:04:00.0] 07: core 270 MHz memory 405 MHz
[   12.544256] nouveau  [     CLK][0000:04:00.0] 0f: core 625 MHz memory 800 MHz
[   12.544434] nouveau  [     CLK][0000:04:00.0] --: core 270 MHz memory 324 MHz
[   12.549194] vga_switcheroo: enabled
[   12.549298] [TTM] Zone  kernel: Available graphics memory: 1966368 kiB
[   12.549300] [TTM] Initializing pool allocator
[   12.549304] [TTM] Initializing DMA pool allocator
[   12.549312] nouveau  [     DRM] VRAM: 2048 MiB
[   12.549313] nouveau  [     DRM] GART: 1048576 MiB
[   12.549316] nouveau E[     DRM] Pointer to TMDS table invalid
[   12.549339] nouveau  [     DRM] DCB version 4.0
[   12.549341] nouveau E[     DRM] Pointer to flat panel table invalid
[   12.556963] nouveau  [     DRM] MM: using COPY0 for buffer copies
[   12.556969] [drm] Initialized nouveau 1.2.1 20120801 for 0000:04:00.0 on minor 1
[   12.977427] Adding 7816188k swap on /dev/sdb9.  Priority:-1 extents:1 across:7816188k FS
[   13.029817] EXT4-fs (sdb7): re-mounted. Opts: errors=remount-ro
[   14.703274] EXT4-fs (sdb6): mounted filesystem with ordered data mode. Opts: (null)
[   14.970555] EXT4-fs (sdb8): mounted filesystem with ordered data mode. Opts: (null)
[   15.679904] systemd-journald[252]: Received request to flush runtime journal from PID 1
[   15.728344] usb 2-6: New USB device found, idVendor=13d3, idProduct=3362
[   15.728349] usb 2-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   15.728352] usb 2-6: Product: Blu


Thread Closed



Users browsing this thread: 1 Guest(s)